CYBERBOND U333
Harmonization Code : 3919.10.80 | Other self-adhesive plastic rolls not exceeding 20 cm wide.
Main features
- Setting Time Below 8 Seconds at 395 nm
- 400% Cured Elongation
- 17.2 to 20.7 N/mm^2 Polycarbonate Bond Strength
Product Description
Cyberbond U333 is a one-part modified acrylate adhesive that cures under UV light for plastic bonding, especially polycarbonate. Typical viscosity is 850 +/- 200 cP. Under 395 nm light at 50 mW/cm^2, typical setting time is below 8 seconds; full strength and solvent resistance develop over 24 hours. Typical cured elongation is 400%, and reported bond strength on polycarbonate is 17.2 to 20.7 N/mm^2.
Key features
- 395 nm setting response: Typical setting time is below 8 seconds under 395 nm exposure at 50 mW/cm^2.
- Cured elongation: Typical cured elongation is 400%.
- Polycarbonate bond strength: Reported bond strength on polycarbonate is 17.2 to 20.7 N/mm^2.
Applications
Bonding plastics, especially polycarbonate.
TDS, SDS & Technical Documents
Technical Specifications
General Properties
Appearance
Light Straw Liquid
Appearance at room temperature.
Physical Properties
Viscosity
850 +/- 200 mPa.s
Viscosity is a measurement of a fluid’s resistance to flow.
Viscosity is commonly measured in centiPoise (cP). One cP is defined as
the viscosity of water and all other viscosities are derived from this base. MPa is another common unit with a 1:1 conversion to cP.
A product like honey would have a much higher viscosity -around 10,000 cPs-
compared to water. As a result, honey would flow much slower out of a tipped glass than
water would.
The viscosity of a material can be decreased with an increase in temperature in
order to better suit an application
Other Properties
RoHS Compliant
Yes
RoHS is a product level compliance based on a European Union Directive which restricts the Use of certain Hazardous Substances in Electrical and Electronic Equipment (RoHS).
Products compliant with this directive do not exceed the allowable amounts of the following restricted materials: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) and polybrominated diphenyl ethers (PBDE), with some limited exemptions
Storage Temperature
8°C to 21 °C
Mechanical Properties
Elongation
400 %
Elongation is the process of lengthening something.
It is a percentage that measures the initial, unstressed, length compared to the length of the material right before it breaks.
It is commonly referred to as Ultimate Elongation or Tensile Elongation at break.
Additional Information
Technical properties
As-supplied / before-processing properties
| Property | Value | Unit | Method / condition |
|---|---|---|---|
| Base compound | Modified acrylate | - | As supplied |
| Appearance | Light straw liquid | - | As supplied |
| Viscosity | 850 +/- 200 | cP | As supplied |
| Specific gravity | 1.1 | g/cc | As supplied |
| Shelf life | 6 | months | Stored unopened |
| Storage condition | 8 to 21 | deg C | In darkness |
| Optimal wavelength | 320 to 425 | nm | UV cure |
| Setting time | Less than 8 | seconds | Polymerized at 395 nm and 50 mW/cm^2 |
Technical properties
UV-cured adhesive properties
Cured-polymer values and substrate-specific bond-strength ranges apply to the exact U333 grade.
| Property | Value | Unit | Method / condition |
|---|---|---|---|
| Full cure time | 24 | hours | UV-cured adhesive |
| Elongation | 400 | % | Cured polymer |
| Hardness | 73 | Shore A | Cured polymer |
| Hardness | 36 | Shore D | Cured polymer |
| Bond strength | 17.2 to 20.7 | N/mm^2 | Polycarbonate substrate |
| Bond strength | 6.9 to 8.3 | N/mm^2 | PETG substrate |
| Bond strength | 6.9 to 10.3 | N/mm^2 | Glass substrate |
